To use a DVR’s hard drive in a computer, we need to connect the drive to a computer system, so as to enable the computer’s operating system to access it. The hard drive, while physically similar to those found in desktop computers, is formatted specifically for use with a DVR. How to connect PC with DVR hard drive?Ī DVR contains a hard drive for storing and recording video. This is because some DVR hard drives support Windows, while some others support Linux. In addition, you need to choose the right DVR system that all security requirements can be fulfilled. On a macOS PC, you can format the DVR storage device to Refs. If you want to use the DVR hard drive on a Linux computer, then you need to format it to Ext4/3/2. So, you can format the DVR hard drive to NTFS if you want to store extra-large files. But the biggest drawback is that you cannot store a single file larger than 4GB in FAT32. On a Windows PC, the FAT32 is the most used file system format since its universal compatibility. The format depends on your computer’s operating system. If you need to format your hard drive manually and would like more information on how to format the drive.įor more information on how to format the hard drive via the device interface, please refer to the information provided below. It is highly recommended to format the hard drive via the device interface first before having to manually format the drive. The hard drive can be formatted manually or via the device’s interface. Reason #7: The Annke system may be defective.Formatting a hard drive will remove all data stored on the device. If possible, please try another SD card on the Annke system. If yes, format the SD card into FAT32, then put it back to the Annke system and try again. Solution: Please check if the SD card can recognized by a computer. Note: Please pay attention to the max storage of the SD card that can be supported by the Annke System. You can try the SD card from different brands. Reason #4: The SD card may not be compatible with the Annke system. Solution: Please refer to the user guide of the Annke system to insert the SD card, pay attention to the guiding mark near the SD card slot. Reason #3: The SD card is not installed in the system properly. Solution: Please format the SD card on the Annke system to have a try. Reason #2: The SD card is not in the 'Normal' status. To configure the OVERWRITE function for your system model, refer to this link: > Solution: Please enable the OVERWRITE of the system, so the system will delete the recording files from the oldest automatically and gradually when the SD card is fully occupied. ![]() Reason #1: SD card storage is fully used. Please send your purchase information to our tech support team, then we will help you further. Solution: If all the above solutions couldn't resolve the issue, the Annke system should be defective. Reason #8: The Annke system may be defective. Ask the Annke support team for the firmware to upgrade your Annke system. Do a factory reset on the Annke system.Ĭ. Reboot the Annke System by unplugging the power supply.ī. Solution: If the above reasons weren't effective, please try below general solutions.Ī. If yes, please format the hard drive into FAT32, then put it back to the Annke system and try again. Note: If you have a desktop PC, you can check if it can recognize this hard drive. Solution: Please try another hard drive on the Annke system if available. Reason #6: The hard drive may be defective. You can try a hard drive from different brand if available. Refer to this instruction for the recommended hard drive for Annke systems: Solution: Please make sure you are using a surveillance hard drive. Reason #5: The hard drive may not be compatible with the Annke system. Solution: Please replace the hard drive cables ( SATA cable + power cable) to have a try. Reason #4: The hard drive cables may be defective. Solution: Please follow this instruction of the installation of a hard drive on the Annke system. Reason #3: The hard drive is not installed in the system properly. Solution: Please format the hard drive on the Annke system to have a try. Reason #2: The hard drive is not in the 'Normal' status. To configure the OVERWRITE for your system model, please contact Annke tech support team: Note: The OVERWRITE setting varies on different models of the Annke system. Solution: Please enable the OVERWRITE of the system, so the system will delete the recording files from the oldest automatically and gradually when the hard drive is fully occupied. Reason #1: The hard drive storage is fully used. This article provides possible reasons and corresponding solutions for the issue of hard drive and SD card. Applies to: All Annke surveillance systems
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |